s s w w i i t t c c h h e e s s m m e e m m s s 2 2 4 4 x x 2 2 4 4 m m a a t t r r i i x x s s w w i i t t c c h h dicon's 24x24 mems matrix switch is an integrated switch module based on dicon's mems 1x24 switch. forty-eight mems 1x24 switches, twenty-four for inputs and the other twenty-four for outputs, are interconnected to form a fully non-blocking, two stage, fan-out/fan-in spanke configuration. under this matrix switch platform, different mems 1xn switches can be used to form customized nxm switch specifications subject to change. copyright ?2006 dicon fiberoptics, inc. all rights reserved. f f e e a a t t u u r r e e s s ? small form factor (less than 8x 11x 1) ? low insertion loss (< 1.7 db) ? low cross talk (<-55 db) ? fast switching time (< 35 ms) ? excellent repeatability (<+/- 0.02 db) ? low power consumption (< 500 mw) ? mems durability and reliability (>10 9 cycles) ? available in other customized configurations a a p p p p l l i i c c a a t t i i o o n n s s the mems 24x24 matrix is used in an optical network to dynamically configure the system. mounting to any network card is easily achieved with its small form factor and 1" thickness. for test and measurement applications, the matrix switch is a simplified alternative solution for cable management and allows users to share resources.
molex 87833-1620 latching type non-latching supply voltage dc 12 v connector type control type power consumption i 2 c, rs232, or rs485 500mw max. s s w w i i t t c c h h e e s s o o r r d d e e r r i i n n g g i i n n f f o o r r m m a a t t i i o o n n m m e e m m s s 2 2 4 4 x x 2 2 4 4 m m a a t t r r i i x x s s w w i i t t c c h h s s w w i i t t c c h h e e s s dicon fiberoptics, inc. 1689 regatta blvd. richmond, ca 94804 tel. (510)620-5000 fax. (510)620-4100 www.diconfiber .com switching time 35 ms max. repeatability +/- 0.02 db max. wdl 0.3 db max. stability pdl 0.05 db max. durability 10 cycles min. 1. il is measured at 1550nm, 23 c. 2. il is for opaque model. power off isolation is same as cross talk. 3. wdl is specified in a +/- 20nm range. 4. repeatability is defined after 100 cycles. 5. over 8 hour period, 23 c tdl 0.3 db max. 0 c to 70 c storage temperature operating temperature -40 o c to +85 o c optical power 500 mw max. fiber type 9/125 m singlemode 3 5 4 1,2 9 o o +/- 0.02 db max. o o insertion loss 1.7 db max. crosstalk -55 db max. back reflection -50 db max. s s p p e e c c i i f f i i c c a a t t i i o o n n s s h h o o u u s s i i n n g g d d i i m m e e n n s s i i o o n n s s e e l l e e c c t t r r i i c c a a l l s s p p e e c c i i f f i i c c a a t t i i o o n n s s mx24x24 p c mx mems mx s c 24x24 24x24 n w r 13 1 1 131 120 1330 12 1 10 110 120 1330 12 1 c t fc fca fc c fcapc c 1 x p l 1 s c i i2c rs2 rs4 i c rs232 rs4 2 f f t t lt smf2 t smf2 l t 1 1 o m singlemode fiber - - - 1 0 0 1 1 3 3 1 1 a a units: mm
|
